1. [多选题]You are bringing up a new Ezonexam switch, and wish to connect it via a trunk to another switch from a different vendor, which uses the IEEE standard for the trunking method. When setting the encapsulation type on the trunk, what should you configure on the Cisco switch?
A. Switch(config) switchport trunk encapsulation isl
B. Switch(config) switchport trunk encapsulation ietf
C. Switch(config-if) switchport trunk encapsulation isl
D. Switch(config-if) switchport trunk encapsulation ietf
E. Switch(config-if) switchport trunk encapsulation dot1q
2. [单选题]为了连接“帧中继”线路，网络中的路由器需要提供的端口类型为（）
A. FastEthernet
B. Serial
C. BRI
D. Ethernet
3. [单选题]对于使用链路状态路由协议的路由器如何选择最佳路线到达子网，下列哪项是正确的（）
A. 路由器会发现链路状态数据库中的最佳路由
B. 通过针对链路状态数据库中的信息运行SPF算法，路由器会计算出最佳路由
C. 路由器将比较每个邻居接收到的更新中为子网列出的标准，并挑选最佳标准路由
D. 路由器会使用具有最低条数的路径
4. [单选题]哪个ACL可允许主机10.220.158.10访问web服务器192.168.3.244()
A. access-list 101 permit tcp host 10.220.158.10 eq 80 host 192.168.3.224
B. access-list 101 permit tcp 10.220.158.10 0.0.0.0 host 192.168.3.224 0.0.0.0 eq 80
C. access-list 101 permit host 10.220.158.10 0.0.0.0 host 192.168.3.224 0.0.0.0 eq 80
D. access-list 101 permit tcp 10.220.158.10 0.0.0.0 host 192.168.3.224 eq 80
5. [单选题]把访问权限表应用到路由器端口的命令是：()
A. permit access-list 101 out
B. ip access-group 101 out
C. apply access-list 101 out
D. access-class 101 out
6. [单选题]路由器下，由一般用户模式进入特权用户模式的命令是：（）
A. enable
B. config
C. interface
D. router
7. [单选题]介质工作在OSI的哪一层（）
A. 物理层
B. 数据链路层(data link layer)
C. 网络层
D. 传输层
8. [单选题]路由器的配置文件startup-config存放在()里
A. RAM
B. ROM
C. FLASH
D. NVRAM
9. [单选题]标准访问控制列表的数字标识范围是（）。
A. 1-50
B. 1-99
C. 1-100
D. 1-199
10. [单选题]After connecting a PC to an available port on a switch, you find that the PC can not access any of the resources on the LAN. No other PC's connected to the switch appear to be having any issues. What is the most likely cause for this problem?
A. The router lacks a routing table entry for the new host
B. The host switch port is assigned to the incorrect VLAN
C. The host MAC address is incorrectly configured
D. A STP instance for the new host has not been initialized
E. The switch does not have the MAC address hard coded in the CAM table.
