1. [多选题]You need to configure a default route on a Ezonexam router. Which command will configure a default route on a router?
A. VE1(config) ip route 0.0.0.0 10.1.1.0 10.1.1.1
B. VE1(config) ip default-route 10.1.1.0
C. VE1(config) ip default-gateway 10.1.1.0
D. VE1(config) ip route 0.0.0.0 0.0.0.0 10.1.1.1
2. [单选题]IP扩展访问列表的数字标示范围是多少（）。
A. 0-99
B. 1-99
C. 100-199
D. 101-200
3. [单选题]路由器上“水平分割”的功能是：()
A. 分离端口
B. 阻止路由环路
C. 简化配置
D. 方便故障处理
4. [单选题]Which command on router EzonexamA will assign the last usable IP address from the 192.168.32.128/28 subnetwork to a router interface?
A. EzonexamA(config-if) ip address 192.168.32.142 255.255.255.240
B. EzonexamA(config-if) ip address 192.168.32.143 255.255.255.240
C. EzonexamA(config-if) ip address 192.168.32.158 255.255.255.240
D. EzonexamA(config-if) ip address 192.168.32.145 255.255.255.240
E. EzonexamA(config-if) ip address 192.168.32.144 255.255.255.240
F. F. EzonexamA(config-if) ip address 192.168.32.158 255.255.255.240
G. G. None of the above
5. [单选题]在OSI七层模型中，介质工作在哪一层()
A. 传输层
B. 会话层(session layer)
C. 物理层
D. 应用层
6. [单选题]At which layer of the OSI model does the protocol that provides the information displayed by the "show cdp neighbors" command operate?
A. Transport
B. Physical
C. Application
D. Data link
E. Network
7. [单选题]You are given a PC, a router, and a cable. Select the correct combination that will allow you to log into router VE1 locally using a terminal emulation program such as HyperTerminal.
A. Connect the PC's COM port to the router's console port using a straight-through cable.
B. Connect the PC's COM port to the router's console port using a rollover cable.
C. Connect the PC's COM port to the router's Ethernet port using a straight-through cable.
D. Connect the PC's Ethernet port to the router's Ethernet port using a rollover cable.
E. Connect the PC's Ethernet port to the router's Ethernet port using a straight- through cable.
F. F. None of the above
8. [单选题]下列哪一个通配符掩码与子网172.16.64.0/27的所有主机匹配（）。
A. 255.255.255.0
B. 255.255.224.0
C. 0.0.0.31
D. 0.0.31.255
9. [多选题]You need to describe the various types of flow control to your co-workers. Which of the following are types of flow control that can be used in a network? (Choose three)
A. Congestion avoidance
B. Windowing
C. Cut-through
D. Buffering
E. Load Balacing
F. F. Fast Forward
10. [单选题]The Ezonexam LAN is upgrading all devices to operate in full duplex. Which statement is true about full-duplex Ethernet in comparison to half-duplex Ethernet?
A. Full-duplex Ethernet uses two wires to send and receive. Half-duplex Ethernet uses one wire to send and receive
B. Full-duplex Ethernet consists of a shared cable segment. Half-duplex Ethernet provides a point-to-point link
C. Full-duplex Ethernet can provide higher throughout than can half-duplex Ethernet of the same bandwidth
D. Full-duplex Ethernet uses a loopback circuit to detect collisions. Half-duplex ethernet uses a jam signal
E. None of the above
