1. [单选题]Your Windows 2000 Server computer has a 10-GB hard disk with two partitions: Drive C and drive D. Windows 2000 Server is installed on Drive D. Both partitions are formatted as NTFS. Your office experiences a power failure that causes your Windows 2000 Server computer to restart.When the computer is restarting, you receive the following error message "NTLDR is missing. Press any key to restart".
A. What should you do?
B. Start the computer by using Windows 2000 Server computer CD-ROM and choose to repair the installation. Select the Recovery Console and copy the NTLDR file on the CD-ROM to the root of the system partition.
C. Start the computer in debugging mode. Copy the NTLDR file on the CD-ROM to the root of the system partition.
D. Start the computer by using the Windows 2000 bootable floppy disk. From a command prompt, run the sfc/scanboot command.
E. Start the computer by using a Windows 2000 bootable floppy disk. Run the File Signature Verification utility.
2. [多选题]You need to install Windows 2000 Server on one of your older Windows NT Server 4.0 computers. The server has dual processors, 2 GB of RAM, a RAID controller with five SCSI hard disks in an array, and a generic 10/100-MB network adapter. You begin the server installation by updating the SCSI firmware.You then start the installation of the Windows 2000 Server operating system. During the next portion of the installation, you receive an error message indicating that no hard disks can be found.
A. You want to successfully install Windows 2000 Server on the computer.
B. What should you do? (Each correct answer presents part of the solution. Choose two)
C. Restart the installation by using the Windows 2000 Installation CD-ROM. Press F3 during the text-mode setup.
D. Restart the installation by using the Windows 2000 Installation CD-ROM. Press F6 during the text-mode setup.
E. Restart the installation by using a MS-DOS boot disk with a CD-ROM driver.
F. Insert a disk with the original SCSI firmware.
G. Insert a disk with the OEM SCSI driver.
3. [单选题]You are the administrator of a SQL Server 2000 computer named SQL1. You want to perform. ad hoc distribution queries against a database that is stored on a SQL Server 2000 computer named SQL2. SQL2 contains several databases, and each of these databases uses a different collation.You want to ensure that comparisons in distributed queries are evaluated correctly. You also want to minimize administrative overhead.
A. How should you configure SQL1?
B. Use the ALTER DATABASE statement to change the collation of the databases on SQL1.
C. Add SQL2 as remote server.
D. Add SQL2 as a linked server. Select the Use Remote Collation check box, and do not specify a collation name.
E. Add SQL2 as a linked server. Select the Use Remote Collation check box, and specify a collation name. Repeat this process once for each database on SQL2.
4. [单选题]You are the network administrator for Ezonexam.com. Your computer has a CD-ROM drive attached to a SCSI adapter. You plan to upgrade your computer from Windows NT Workstation 4.0 to Windows 2000 Professional. You determine that the SCSI adapter is not included on the current Hardware Compatibility List (HCL) and that the original SCSI drivers that you used for Windows NT are not compatible with Windows 2000 Professional.You want to upgrade your computer to Windows 2000 Professional.
A. What should you do?
B. Replace the SCSI adapter card with a Windows 2000 Professional compatible SCSI adapter. Start the installation from the Windows 2000 Professional CD-ROM. Add the new adapter card drivers when you are prompted.
C. Obtain Windows 2000 drivers from the SCSI adapter manufacturer. Copy the drivers to C:\Winnt folder. Start the installation from the Windows 2000 Professional CD-ROM.
D. Obtain Windows 2000 drivers from the SCSI adapter manufacturer. Start the installation by using the Windows 2000 Professional CD-ROM. Add the new adapter card drivers when you are prompted.
E. Modify Config.sys to use your existing SCSI adapter and existing CD-ROM drive. Using Windows NT 4.0, start the installation by running Winnt32.exe from the I386 folder on the Windows 2000 Professional CD-ROM.
5. [单选题]Your network includes Windows 98 computers and Windows 2000 Server computers. You are adding a new computer to the network, and you plan to install Windows 2000 Server on the new computer. The computer has one 20-GB hard disk with no partitions defined.The Windows 2000 Server CD-ROM is unavailable. You want install Windows 2000 Server from source files that are located on a server on the network. You also want the entire hard disk of the new computer to be used for the system partition.
A. What should you do?
B. On another Windows 2000 computer, use Makebt32.exe to create installation startup disks. Start the new computer by using the first disk.
C. On another Windows 2000 computer, format a floppy disk. Copy NTLDR, Boot.ini, Ntdetect.com, Ntbootdd.sys to this disk. Start the new computer by using the disk.
D. Start the new computer by using a Windows 98 network boot disk. Connect to the network server. Run Dsclient.exe. Create and format a 20-GB FAT32 partition.
E. Start the new computer by using a Windows 98 network boot disk. Create and format a single FAT32 partition. Connect to the network server. Run Winnt.exe.
F. Start the computer by using a Windows 98 network boot disk. Create and format a single FAT32 partition. Start the new computer by using a Windows 2000 Emergency Repair Disk.
